Difference between revisions of "Docs/Troubleshooting Guide"

From Userful Support
Jump to navigationJump to search
Line 35: Line 35:
  
 
* Non-broadcast resolutions not supported  
 
* Non-broadcast resolutions not supported  
:If the source you're trying to capture is a laptop or PC and your display is a not a Broadcast resolution, duplicating its screen to the capture card would not work with Linux or MacOS.<br>
+
:If the source you're trying to capture is a laptop or PC and your display is a not a Broadcast resolution, duplicating its screen to the capture card would not work with Linux or MacOS<br>
 
: Resolutions such as 1366x768, 1440x900 or 1600x900 are only supported in Windows (Windows supports cloning of displays with different resolutions). To fix this:
 
: Resolutions such as 1366x768, 1440x900 or 1600x900 are only supported in Windows (Windows supports cloning of displays with different resolutions). To fix this:
 
:* in Windows (set your desktop to Duplicate, then change the capture card resolution in the Display Settings)
 
:* in Windows (set your desktop to Duplicate, then change the capture card resolution in the Display Settings)
Line 42: Line 42:
  
 
:This will enable your laptop to correctly detect the display resolution from the capture card.
 
:This will enable your laptop to correctly detect the display resolution from the capture card.
 +
 +
===Network Troubleshooting===
 +
====Sluggishness when playing 6k content over 1 gig NIC====
 +
* Ensure that you have 10Gig NIC installed on the Userful host and a 10Gig uplink port on the switch<br>
 +
* Make sure to use Cat 6A cable for connecting Userful host to 10Gig uplink port on the switch
 +
'''Note:''' Only the uplink port of the switch needs to support 10Gbps, the remaining ports which connect to the zero clients can be 1Gbps
 +
 +
====Sluggishness - when playing large number of videos====
 +
* Click [[Image:Mirror_Group.png|30px]] icon on the right corner of an existing source and enable "mirroring", when playing identical videos, or
 +
* Install an [[Docs/Nvidia Offload Support#Supported_Cards|Offload Card]] to double the performance of Userful host, or
 +
* Replace or re-encode the videos if they are inefficient, or
 +
* Re-encode videos using an optimal [[Docs/Optimal_Video_Wall_Guidelines#Supported_Video_Codecs_and_Image_formats |format]], if the videos have higher than necessary bit rate or frame rate
 +
 +
====Latency issues while playing video from a digital video camera====
 +
Ensure that you have a direct connection between your camera and [[Docs/Supported_Capture_Cards|Supported Capture Card]] in the Userful host <br>
 +
 +
'''Note:''' Some webcams output RTSP streams and these can be connected via the [[Docs/Mapping/Network_Streamer |Network Streamer]] source
 +
 +
==== How can I overcome the issues of network outage ====
 +
Connect additional Userful host (backup server) and use "Failover Group Settings" feature of UCC
 +
* Go to <tt>Control Center > Settings > Failover Group settings</tt>
 +
* Enable Failover to proceed <br>
 +
Please visit [[Docs/Failover |Failover]] for detailed instructions
  
 
===Zero Clients===
 
===Zero Clients===
 
==== Network zero client(s) show instability ====
 
==== Network zero client(s) show instability ====
 
If one or more network zero clients freezes or drops its session:
 
If one or more network zero clients freezes or drops its session:
* Ensure that the network zero client device(s) are set to static IPs and are isolated from other traffic as much as possible using separate switching hardware.
+
* Ensure that the network zero client device(s) are set to static IPs and are isolated from other traffic as much as possible using separate switching hardware
 
* Ensure all zero clients have updated firmware
 
* Ensure all zero clients have updated firmware
For more details visit [[Docs/Managing_Displays#Configure_Network_Settings_for_Display|Managing Displays]].
+
For more details visit [[Docs/Managing_Displays#Configure_Network_Settings_for_Display|Managing Displays]]
 
<!--
 
<!--
 
===== While configuring network settings for the network station, display freezes in an abnormal state =====
 
===== While configuring network settings for the network station, display freezes in an abnormal state =====
Line 54: Line 77:
 
-->
 
-->
 
====Blue LED on the device does not turn on ====
 
====Blue LED on the device does not turn on ====
* Check the power source of the device.
+
* Check the power source of the device
* Check the connection to the outlet and power adapter.
+
* Check the connection to the outlet and power adapter
* Ensure that the blue LED is not burnt out.
+
* Ensure that the blue LED is not burnt out
  
 
====The device does not turn on after plugging to the switch ====
 
====The device does not turn on after plugging to the switch ====
 
* Connect the same device on a different port on the switch where another device was working properly, or
 
* Connect the same device on a different port on the switch where another device was working properly, or
* Connect another device that is working properly to the same power adapter.
+
* Connect another device that is working properly to the same power adapter
  
 
==== USB zero client device(s) show instability ====
 
==== USB zero client device(s) show instability ====
Line 67: Line 90:
 
* Do the physical reset of the USB zero client device
 
* Do the physical reset of the USB zero client device
  
 
+
{{forcewhitespace}}
 
[[Category: Docs]]
 
[[Category: Docs]]

Revision as of 20:57, 5 May 2017


Copyright © 2017 Userful Corporation. All rights reserved.
(Updated 2017.05.05)

To return to the main documentation page, Click Here.


Introduction

This document presents solutions to the most commonly encountered troubleshooting tasks. For a comprehensive list of troubleshooting tips, please visit http://support.userful.com.

Identify the Issue

If you know what component of your system is causing an issue, please refer to that software or hardware's documentation for help and support, else follow the necessary steps depending on the issues.

Capture Cards

This section outlines the solution to the common problems encountered while using Capture Cards.

Blackmagic Card not detected in the Control Center

  • Make sure the supported capture card is installed and supported by the system
  • Ensure that the firmware is updated.
Open terminal and at the command line type in the following command (sudo or root privileges are required through out the procedure) and reboot the system:
   $ sudo BlackmagicFirmwareUpdater update 0 
  • Ensure that the driver is installed via Control Center > Settings > Check for Available Packages and the system is rebooted after all the updates.

Color Bars when launching the display or video wall

Verify that the correct device is selected while creating the source, or the input device is plugged into the correct port on the capture card.

Unable to play external media devices on Userful host

  • Install a Supported Capture Card on Userful host and plug the device to the capture card, if the content is not HDCP-encrypted, then configure the source to play the content. OR
  • Connect the external media player to the Supported Capture Card on the Userful host via HDMI splitters/ HDMI switches for capturing HDCP-encrypted content, then configure the source to play the content.

Note: HDMI splitters/ HDMI switches aren't officially HDCP compliant but in many cases can allow playback of HDCP-encrypted content on non-compliant devices.

Black Screen(s) when launching the displays or video wall

  • Verify that the color space of the capture source is correct for your card. Please see Supported Capture Cards for details, if in doubt use YUV or YCbCr, or
  • Non-broadcast resolutions not supported
If the source you're trying to capture is a laptop or PC and your display is a not a Broadcast resolution, duplicating its screen to the capture card would not work with Linux or MacOS
Resolutions such as 1366x768, 1440x900 or 1600x900 are only supported in Windows (Windows supports cloning of displays with different resolutions). To fix this:
  • in Windows (set your desktop to Duplicate, then change the capture card resolution in the Display Settings)
  • in Linux (Verify that the mirror displays option is uncheked in the Display Settings)
  • in Mac (Verify that the mirror displays option is uncheked in the Display Settings)
This will enable your laptop to correctly detect the display resolution from the capture card.

Network Troubleshooting

Sluggishness when playing 6k content over 1 gig NIC

  • Ensure that you have 10Gig NIC installed on the Userful host and a 10Gig uplink port on the switch
  • Make sure to use Cat 6A cable for connecting Userful host to 10Gig uplink port on the switch

Note: Only the uplink port of the switch needs to support 10Gbps, the remaining ports which connect to the zero clients can be 1Gbps

Sluggishness - when playing large number of videos

  • Click Mirror Group.png icon on the right corner of an existing source and enable "mirroring", when playing identical videos, or
  • Install an Offload Card to double the performance of Userful host, or
  • Replace or re-encode the videos if they are inefficient, or
  • Re-encode videos using an optimal format, if the videos have higher than necessary bit rate or frame rate

Latency issues while playing video from a digital video camera

Ensure that you have a direct connection between your camera and Supported Capture Card in the Userful host

Note: Some webcams output RTSP streams and these can be connected via the Network Streamer source

How can I overcome the issues of network outage

Connect additional Userful host (backup server) and use "Failover Group Settings" feature of UCC

  • Go to Control Center > Settings > Failover Group settings
  • Enable Failover to proceed

Please visit Failover for detailed instructions

Zero Clients

Network zero client(s) show instability

If one or more network zero clients freezes or drops its session:

  • Ensure that the network zero client device(s) are set to static IPs and are isolated from other traffic as much as possible using separate switching hardware
  • Ensure all zero clients have updated firmware

For more details visit Managing Displays

Blue LED on the device does not turn on

  • Check the power source of the device
  • Check the connection to the outlet and power adapter
  • Ensure that the blue LED is not burnt out

The device does not turn on after plugging to the switch

  • Connect the same device on a different port on the switch where another device was working properly, or
  • Connect another device that is working properly to the same power adapter

USB zero client device(s) show instability

If USB zero clients drops or freezes:

  • Ensure that USB zero client devices are connected to the USB 2.0 ports and use high-quality USB 2.0 compliant cables, and
  • Do the physical reset of the USB zero client device